Installing the RAID controller Адаптер thinkserver Lenovo Tower Server - TS100 (ThinkServer) - Type 6431

Страница: 58 из 96

background image

4.

   

Remove

 

the

 

hard

 

disk

 

drive

 

fan

 

assembly:

 

a.

   

Disconnect

 

the

 

hard

 

disk

 

drive

 

fan

 

assembly

 

cable

 

from

 

the

 

system

 

board

 

and

 

make

 

a

 

note

 

of

 

where

 

the

 

cable

 

was

 

connected

 

for

 

later

 

installation.

 

b.

   

Remove

 

all

 

hard

 

disk

 

drives.

 

c.

   

Press

 

and

 

hold

 

the

 

drive

 

cage

 

release

 

tab

 

on

 

the

 

side

 

of

 

the

 

drive

 

cage;

 

then,

 

rotate

 

the

 

drive

 

cage

 

out

 

of

 

the

 

chassis

 

until

 

the

 

retaining

 

tab

 

on

 

top

 

of

 

the

 

cage

 

locks

 

into

 

place.

 

d.

   

Pull

 

out

 

on

 

the

 

hard

 

disk

 

drive

 

fan

 

assembly

 

release

 

tabs

 

(at

 

the

 

blue

 

dots);

 

then,

 

rotate

 

the

 

hard

 

disk

 

drive

 

fan

 

assembly

 

away

 

from

 

the

 

drive

 

cage

 

slightly.

 

5.

   

Disconnect

 

the

 

signal

 

and

 

power

 

cables

 

and

 

the

 

existing

 

SAS/SATA

 

controller

 

(if

 

one

 

is

 

installed);

 

then,

 

remove

 

the

 

controller

 

from

 

the

 

server.

 

 

6.

   

Touch

 

the

 

static-protective

 

package

 

that

 

contains

 

the

 

ServeRAID-MR10i

 

SAS/SATA

 

controller

 

to

 

any

 

unpainted

 

metal

 

surface

 

on

 

the

 

server.

 

Then,

 

remove

 

the

 

ServeRAID-MR10i

 

SAS/SATA

 

controller

 

from

 

the

 

package.

 

 

7.

   

Align

 

the

 

ServeRAID-MR10i

 

SAS/SATA

 

controller

 

so

 

that

 

the

 

keys

 

align

 

correctly

 

with

 

the

 

connector

 

on

 

the

 

system

 

board.

 

Attention:

  

Incomplete

 

insertion

 

might

 

cause

 

damage

 

to

 

the

 

system

 

board

 

or

 

the

 

ServeRAID-MR10i

 

controller.

  

 

 

1

 

Hard

 

disk

 

drive

 

cable

 

connector

 

4

 

-

 

7

 

4

 

ServeRAID-MR10i

 

SAS/SATA

 

controller

 

2

 

Hard

 

disk

 

drive

 

cable

 

connector

 

0

 

-

 

3

 

5

 

Hard

 

disk

 

drive

 

cable

 

4

 

-

 

7

 

3

 

Battery

 

6

 

Hard

 

disk

 

drive

 

cable

 

0

 

-

 

3

 

 

44

 

ThinkServer

 

TS100

 

Types

 

6431,

 

6432,

 

6433,

 

and

 

6434:

 

User

 

Guide