Installing an adapter Адаптер thinkserver Lenovo Tower Server - TS100 (ThinkServer) - Type 6431

Страница: 55 из 96

background image

v

   

The

 

server

 

scans

 

PCI

 

Express

 

x8

 

slot

 

1,

 

PCI

 

Express

 

x4

 

slot

 

2,

 

PCI-X

 

slot

 

3,

 

and

 

PCI

 

slots

 

4

 

and

 

5

 

to

 

assign

 

system

 

resources.

 

Then,

 

the

 

server

 

starts

 

the

 

PCI

 

devices

 

in

 

the

 

following

 

order,

 

if

 

you

 

have

 

not

 

changed

 

the

 

default

 

startup

 

sequence:

 

PCI

 

Express

 

x8

 

slot

 

1,

 

PCI

 

Express

 

x4

 

slot

 

2,

 

PCI-X

 

slot

 

3,

 

PCI

 

slot

 

4,

 

and

 

PCI

 

slot

 

5.

 

v

   

For

 

a

 

list

 

of

 

supported

 

optional

 

devices

 

for

 

the

 

server,

 

go

 

to:

 

http://www.lenovo.com/thinkserver.

 

Attention:

  

Static

 

electricity

 

that

 

is

 

released

 

to

 

internal

 

server

 

components

 

when

 

the

 

server

 

is

 

powered-on

 

might

 

cause

 

the

 

server

 

to

 

stop,

 

which

 

might

 

result

 

in

 

the

 

loss

 

of

 

data.

 

To

 

avoid

 

this

 

potential

 

problem,

 

always

 

use

 

an

 

electrostatic-discharge

 

wrist

 

strap

 

or

 

other

 

grounding

 

system

 

when

 

you

 

work

 

inside

 

the

 

server

 

with

 

the

 

power

 

on.

 

See

 

“System-board

 

optional-device

 

connectors”

 

on

 

page

 

16

 

for

 

the

 

locations

 

of

 

the

 

expansion

 

slots

 

and

 

the

 

systems-management

 

Ethernet

 

connector.

 

To

 

install

 

an

 

adapter,

 

complete

 

the

 

following

 

steps:

 

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

19.

 

 

2.

   

Turn

 

off

 

the

 

server

 

and

 

peripheral

 

devices

 

and

 

disconnect

 

all

 

external

 

cables

 

and

 

power

 

cords;

 

then,

 

remove

 

the

 

side

 

cover.

 

See

 

“Removing

 

the

 

side

 

cover”

 

on

 

page

 

23.

 

 

3.

   

Follow

 

the

 

cabling

 

instructions,

 

if

 

any,

 

that

 

come

 

with

 

the

 

adapter.

 

Route

 

the

 

adapter

 

cables

 

before

 

you

 

install

 

the

 

adapter.

 

 

4.

   

Follow

 

the

 

instructions

 

that

 

come

 

with

 

the

 

adapter

 

to

 

set

 

jumpers

 

or

 

switches,

 

if

 

any.

 

 

5.

   

Rotate

 

the

 

rear

 

adapter-retention

 

bracket

 

to

 

the

 

open

 

position

 

and

 

remove

 

it

 

from

 

the

 

server.

 

 

Chapter

 

2.

 

Installing

 

optional

 

devices

 

41