Installing a simple-swap SATA hard disk drive Адаптер thinkserver Lenovo Tower Server - TS100 (ThinkServer) - Type 6431

Страница: 51 из 96

background image

IDs

 

for

 

hot-swap

 

hard

 

disk

 

drives

 

On

 

some

 

models,

 

the

 

hot-swap-drive

 

backplane

 

controls

 

the

 

IDs

 

of

 

the

 

internal

 

hot-swap

 

drive

 

bays.

 

The

 

following

 

table

 

lists

 

the

 

IDs

 

of

 

the

 

hard

 

disk

 

drives

 

and

 

backplane

 

that

 

are

 

connected

 

to

 

one

 

channel

 

in

 

the

 

hot-swap

 

models.

 

In

 

the

 

typical

 

configuration,

 

the

 

standard

 

hard

 

disk

 

drives

 

and

 

backplane

 

are

 

connected

 

to

 

channel

 

A.

 

This

 

table

 

applies

 

only

 

to

 

server

 

models

 

that

 

support

 

four

 

hard

 

disk

 

drives.

 

 

Table

 

9.

 

IDs

 

of

 

the

 

hot-swap

 

drives

 

(models

 

with

 

four

 

drive

 

bays)

 

Drive

 

bay

 

ID

 

4

 

0

 

5

 

1

 

6

 

2

 

7

 

3

  

If

 

your

 

server

 

model

 

is

 

the

 

type

 

that

 

supports

 

eight

 

2.5-inch

 

hot-swap

 

SAS

 

drives,

 

the

 

IDs

 

of

 

the

 

hard

 

disk

 

drives

 

are

 

shown

 

in

 

the

 

following

 

table.

 

 

Table

 

10.

 

IDs

 

of

 

the

 

hot-swap

 

drives

 

(models

 

with

 

eight

 

drive

 

bays)

 

Drive

 

bay

 

ID

 

4

 

0

 

5

 

1

 

6

 

2

 

7

 

3

 

8

 

4

 

9

 

5

 

10

 

6

 

11

 

7

  

Installing

 

a

 

simple-swap

 

SATA

 

hard

 

disk

 

drive

 

Some

 

server

 

models

 

support

 

3.5-inch

 

simple-swap

 

SATA

 

hard

 

disk

 

drives,

 

which

 

are

 

accessible

 

from

 

the

 

front

 

of

 

the

 

server.

 

You

 

must

 

disconnect

 

all

 

power

 

from

 

the

 

server

 

before

 

you

 

remove

 

or

 

install

 

simple-swap

 

drives.

 

Before

 

you

 

install

 

a

 

simple-swap

 

SATA

 

hard

 

disk

 

drive,

 

read

 

the

 

following

 

information:

 

v

   

You

 

can

 

install

 

four

 

simple-swap

 

SATA

 

hard

 

disk

 

drives

 

in

 

the

 

simple-swap

 

models

 

(7-drive-bay

 

models)

 

only.

 

v

   

Install

 

the

 

drives

 

starting

 

from

 

the

 

top

 

bay

 

to

 

the

 

bottom

 

bay

 

(bay

 

4,

 

5,

 

6,

 

and

 

then

 

7).

 

v

   

The

 

four

 

simple-swap

 

SATA

 

hard

 

disk

 

drives

 

connect

 

to

 

the

 

SATA

 

0

 

through

 

SATA

 

3

 

connectors

 

on

 

the

 

system

 

board

 

as

 

follows:

 

   

The

 

drive

 

in

 

bay

 

4

 

connects

 

to

 

the

 

SATA

 

0

 

connector

 

on

 

the

 

system

 

board.

 

   

The

 

drive

 

in

 

bay

 

5

 

connects

 

to

 

the

 

SATA

 

1

 

connector

 

on

 

the

 

system

 

board.

 

   

The

 

drive

 

in

 

bay

 

6

 

connects

 

to

 

the

 

SATA

 

2

 

connector

 

on

 

the

 

system

 

board.

 

   

The

 

drive

 

in

 

bay

 

7

 

connects

 

to

 

the

 

SATA

 

3

 

connector

 

on

 

the

 

system

 

board.

 

Attention:

  

Simple-swap

 

hard

 

disk

 

drives

 

are

 

not

 

hot-swappable.

 

Disconnect

 

all

 

power

 

from

 

the

 

server

 

before

 

you

 

remove

 

or

 

install

 

a

 

simple-swap

 

hard

 

disk

 

drive.

 

Chapter

 

2.

 

Installing

 

optional

 

devices

 

37