Installing a tape drive Адаптер thinkserver Lenovo Tower Server - TS100 (ThinkServer) - Type 6431

Страница: 47 из 96

background image

1

 

Release

 

buttons

 

2

 

Drive

 

retainer

 

clip

  

 

9.

   

If

 

you

 

are

 

installing

 

a

 

5.25-inch

 

drive

 

in

 

bay

 

2,

 

slide

 

the

 

drive

 

into

 

the

 

bay.

 

If

 

you

 

are

 

installing

 

a

 

3.5-inch

 

drive

 

in

 

bay

 

2,

 

you

 

must

 

attach

 

the

 

5.25-inch.

 

conversion

 

kit

 

to

 

the

 

3.5-inch

 

drive.

 

Note:

 

An

 

optional

 

diskette

 

drive

 

can

 

be

 

installed

 

in

 

bay

 

3.

 

10.

   

Connect

 

one

 

end

 

of

 

the

 

applicable

 

signal

 

cable

 

into

 

the

 

rear

 

of

 

the

 

drive

 

and

 

make

 

sure

 

that

 

the

 

other

 

end

 

of

 

this

 

cable

 

is

 

connected

 

into

 

the

 

applicable

 

SATA

 

connector

 

on

 

the

 

system

 

board.

 

11.

   

Route

 

the

 

signal

 

cable

 

so

 

that

 

it

 

does

 

not

 

block

 

the

 

airflow

 

to

 

the

 

rear

 

of

 

the

 

drives

 

or

 

go

 

over

 

the

 

microprocessor

 

and

 

dual

 

inline

 

memory

 

modules

 

(DIMMs).

 

12.

   

If

 

you

 

have

 

another

 

drive

 

to

 

install

 

or

 

remove,

 

do

 

so

 

now.

 

13.

   

Connect

 

the

 

power

 

cable

 

to

 

the

 

rear

 

of

 

the

 

drive.

 

The

 

connectors

 

are

 

keyed

 

and

 

can

 

be

 

inserted

 

only

 

one

 

way.

If

 

you

 

have

 

other

 

devices

 

to

 

install

 

or

 

remove,

 

do

 

so

 

now;

 

otherwise,

 

go

 

to

 

“Completing

 

the

 

installation”

 

on

 

page

 

50.

 

Installing

 

a

 

tape

 

drive

 

To

 

install

 

a

 

tape

 

drive3,

 

complete

 

the

 

following

 

steps:

 

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

19.

 

 

2.

   

Turn

 

off

 

the

 

server

 

and

 

peripheral

 

devices,

 

and

 

disconnect

 

the

 

power

 

cords

 

and

 

all

 

external

 

cables.

 

 

3.

   

Remove

 

the

 

side

 

cover

 

(see

 

“Removing

 

the

 

side

 

cover”

 

on

 

page

 

23).

 

 

4.

   

Remove

 

the

 

two-piece

 

bezel

 

(see

 

“Removing

 

the

 

two-piece

 

bezel”

 

on

 

page

 

24).

 

 

5.

   

Use

 

a

 

screwdriver

 

to

 

pry

 

the

 

filler

 

panel

 

2

 

and

 

EMC

 

shield

 

1

 

away

 

from

 

the

 

server.

 

 

Chapter

 

2.

 

Installing

 

optional

 

devices

 

33