Installing a microprocessor Адаптер thinkserver Lenovo Tower Server - TD100 (ThinkServer) - Type 4205

Страница: 58 из 98

background image

c.

   

Make

 

sure

 

that

 

the

 

retaining

 

clips

 

are

 

in

 

the

 

locked

 

position

 

when

 

the

 

VRM

 

is

 

firmly

 

seated

 

in

 

the

 

connector.

 

8.

   

Install

 

the

 

microprocessor:

 

a.

   

Touch

 

the

 

static-protective

 

package

 

that

 

contains

 

the

 

microprocessor

 

to

 

any

 

unpainted

 

metal

 

surface

 

on

 

the

 

server.

 

Then,

 

remove

 

the

 

microprocessor

 

from

 

the

 

package.

 

b.

   

Remove

 

the

 

protective

 

cover,

 

tape,

 

or

 

label

 

from

 

the

 

surface

 

of

 

the

 

microprocessor

 

socket,

 

if

 

any

 

is

 

present.

 

c.

   

Open

 

the

 

microprocessor

 

bracket

 

frame

 

1.

 

d.

   

Rotate

 

the

 

release

 

lever

 

2

 

on

 

the

 

microprocessor

 

socket

 

from

 

its

 

closed

 

and

 

locked

 

position

 

to

 

its

 

fully

 

open

 

position.

 

 

Attention:

  

Make

 

sure

 

that

 

the

 

release

 

lever

 

on

 

the

 

microprocessor

 

socket

 

is

 

in

 

the

 

fully

 

open

 

position

 

before

 

you

 

insert

 

the

 

microprocessor

 

in

 

the

 

socket.

 

Failure

 

to

 

do

 

so

 

might

 

result

 

in

 

permanent

 

damage

 

to

 

the

 

microprocessor,

 

microprocessor

 

socket,

 

and

 

system

 

board.

  

 

 

Attention:

   

v

   

Do

 

not

 

use

 

excessive

 

force

 

when

 

pressing

 

the

 

microprocessor

 

into

 

the

 

socket.

 

v

   

Make

 

sure

 

that

 

the

 

microprocessor

 

is

 

oriented

 

and

 

aligned

 

with

 

land

 

number

 

1

 

in

 

the

 

socket

 

before

 

you

 

try

 

to

 

close

 

the

 

lever.

e.

   

Align

 

the

 

microprocessor

1

 

with

 

the

 

socket

 

(note

 

the

 

alignment

 

mark

 

2

 

and

 

the

 

position

 

of

 

the

 

notches);

 

then,

 

carefully

 

place

 

the

 

microprocessor

 

on

 

the

 

socket

 

4

 

and

 

close

 

the

 

microprocessor

 

bracket

 

frame.

 

  

  

f.

   

Carefully

 

close

 

the

 

release

 

lever

 

3

 

to

 

secure

 

the

 

microprocessor

 

in

 

the

 

socket.

 

9.

   

Install

 

the

 

heat

 

sink.

 

 

Attention:

  

Do

 

not

 

touch

 

the

 

thermal

 

grease

 

on

 

the

 

bottom

 

of

 

the

 

heat

 

sink

 

or

 

set

 

down

 

the

 

heat

 

sink

 

after

 

you

 

remove

 

the

 

plastic

 

cover.

 

Touching

 

the

 

thermal

 

grease

 

will

 

contaminate

 

it.

 

a.

   

Make

 

sure

 

that

 

the

 

heat-sink

 

lever

 

4

 

is

 

in

 

the

 

open

 

position.

 

b.

   

Remove

 

the

 

plastic

 

protective

 

cover

 

from

 

the

 

bottom

 

of

 

the

 

heat

 

sink

 

1.

 

c.

   

Align

 

the

 

heat

 

sink

 

1

 

above

 

the

 

microprocessor

 

2

 

with

 

the

 

thermal-grease

 

side

 

down.

 

Press

 

firmly

 

on

 

the

 

heat

 

sink.

 

 

44

 

ThinkServer

 

TD100

 

and

 

TD100x

 

Types

 

4203,

 

4204,

 

4205,

 

4206,

 

6398,

 

6399,

 

6419,

 

and

 

6429:

 

User

 

Guide