Installing a simple-swap SATA hard disk drive (TD100 models only) Адаптер thinkserver Lenovo Tower Server - TD100 (ThinkServer) - Type 4205

Страница: 52 из 98

background image

Device

 

ID

 

Drive

 

bay

 

11

 

7

  

Installing

 

a

 

simple-swap

 

SATA

 

hard

 

disk

 

drive

 

(TD100

 

models

 

only)

 

Some

 

server

 

models

 

come

 

with

 

simple-swap

 

SATA

 

hard

 

disk

 

drives

 

that

 

are

 

accessible

 

from

 

the

 

front

 

of

 

the

 

server.

 

Before

 

you

 

install

 

a

 

simple-swap

 

SATA

 

hard

 

disk

 

drive,

 

read

 

the

 

following

 

information:

 

v

   

You

 

must

 

turn

 

off

 

the

 

server

 

before

 

installing

 

simple-swap

 

drives

 

in

 

the

 

server.

 

v

   

You

 

can

 

install

 

only

 

four

 

simple-swap

 

SATA

 

hard

 

disk

 

drives

 

in

 

the

 

server.

 

v

   

The

 

sequence

 

for

 

installing

 

the

 

hard

 

disk

 

drives

 

is

 

to

 

install

 

the

 

drives

 

starting

 

from

 

the

 

bottom

 

bay

 

(bay

 

7)

 

and

 

go

 

up

 

to

 

the

 

top

 

bay

 

(bay

 

4).

To

 

install

 

a

 

simple-swap

 

hard

 

disk

 

drive,

 

complete

 

the

 

following

 

steps:

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

20.

 

2.

   

Turn

 

off

 

the

 

server

 

and

 

peripheral

 

devices

 

and

 

disconnect

 

all

 

external

 

cables

 

and

 

power

 

cords.

 

3.

   

Unlock

 

the

 

side

 

cover

 

(you

 

cannot

 

open

 

or

 

remove

 

the

 

bezel

 

without

 

unlocking

 

the

 

side

 

cover).

 

4.

   

Remove

 

the

 

bezel

 

(see

 

“Removing

 

the

 

bezel”

 

on

 

page

 

24.

 

5.

   

Touch

 

the

 

static-protective

 

package

 

that

 

contains

 

the

 

drive

 

to

 

any

 

unpainted

 

metal

 

surface

 

on

 

the

 

server;

 

then,

 

remove

 

the

 

drive

 

from

 

the

 

package

 

and

 

place

 

it

 

on

 

a

 

static-protective

 

surface.

 

6.

   

Align

 

the

 

drive

 

assembly

 

with

 

the

 

guide

 

rails

 

in

 

the

 

bay

 

(the

 

connector

 

end

 

of

 

the

 

drive

 

goes

 

in

 

first).

 

7.

   

Press

 

the

 

drive

 

assembly

 

loops

 

toward

 

each

 

other;

 

then,

 

carefully

 

slide

 

the

 

drive

 

assembly

 

into

 

the

 

drive

 

bay

 

until

 

it

 

stops

 

and

 

release

 

the

 

loops.

 

Note:

 

Do

 

not

 

release

 

the

 

loops

 

on

 

the

 

drive

 

assembly

 

until

 

it

 

is

 

completely

 

seated.

 

38

 

ThinkServer

 

TD100

 

and

 

TD100x

 

Types

 

4203,

 

4204,

 

4205,

 

4206,

 

6398,

 

6399,

 

6419,

 

and

 

6429:

 

User

 

Guide