Turning on the server Адаптер thinkserver Lenovo Tower Server - TD100 (ThinkServer) - Type 4205

Страница: 27 из 98

background image

Video

 

connector

 

Connect

 

a

 

monitor

 

to

 

this

 

connector.

 

USB

 

connectors

 

Connect

 

USB

 

devices

 

to

 

these

 

connectors.

 

Ethernet

 

connectors

 

Use

 

these

 

connectors

 

to

 

connect

 

the

 

server

 

to

 

a

 

network.

 

Ethernet

 

transmit/receive

 

activity

 

LED

 

This

 

LED

 

is

 

on

 

the

 

Ethernet

 

connector

 

on

 

the

 

rear

 

of

 

the

 

server.

 

When

 

this

 

LED

 

is

 

lit,

 

it

 

indicates

 

that

 

there

 

is

 

activity

 

between

 

the

 

server

 

and

 

the

 

network.

 

Ethernet

 

link

 

status

 

LED

 

This

 

LED

 

is

 

on

 

the

 

Ethernet

 

connector

 

on

 

the

 

rear

 

of

 

the

 

server.

 

When

 

this

 

LED

 

is

 

lit,

 

it

 

indicates

 

that

 

there

 

is

 

an

 

active

 

connection

 

on

 

the

 

Ethernet

 

port.

Server

 

power

 

features

 

When

 

the

 

server

 

is

 

connected

 

to

 

an

 

ac

 

power

 

source

 

but

 

is

 

not

 

turned

 

on,

 

the

 

operating

 

system

 

does

 

not

 

run,

 

and

 

all

 

core

 

logic

 

except

 

for

 

the

 

service

 

processor

 

(the

 

baseboard

 

management

 

controller

 

(BMC)

 

or

 

optional

 

Remote

 

Supervisor

 

Adapter

 

II

 

SlimLine)

 

is

 

shut

 

down;

 

however,

 

the

 

server

 

can

 

respond

 

to

 

remote

 

requests

 

from

 

the

 

service

 

processor,

 

such

 

as

 

a

 

remote

 

request

 

to

 

turn

 

on

 

the

 

server.

 

The

 

power-on

 

LED

 

flashes

 

to

 

indicate

 

that

 

the

 

server

 

is

 

connected

 

to

 

ac

 

power

 

but

 

not

 

turned

 

on.

 

Turning

 

on

 

the

 

server

 

Approximately

 

20

 

seconds

 

after

 

the

 

server

 

is

 

connected

 

to

 

ac

 

power,

 

the

 

power-control

 

button

 

becomes

 

active,

 

and

 

one

 

or

 

more

 

fans

 

might

 

start

 

running

 

to

 

provide

 

cooling

 

while

 

the

 

server

 

is

 

connected

 

to

 

power.

 

You

 

can

 

turn

 

on

 

the

 

server

 

and

 

start

 

the

 

operating

 

system

 

by

 

pressing

 

the

 

power-control

 

button.

 

The

 

server

 

also

 

can

 

be

 

turned

 

on

 

in

 

any

 

of

 

the

 

following

 

ways:

 

v

   

If

 

a

 

power

 

failure

 

occurs

 

while

 

the

 

server

 

is

 

turned

 

on,

 

the

 

server

 

will

 

restart

 

automatically

 

when

 

power

 

is

 

restored.

 

v

   

If

 

your

 

operating

 

system

 

supports

 

the

 

systems-management

 

software

 

for

 

an

 

optional

 

Remote

 

Supervisor

 

Adapter

 

II

 

SlimLine,

 

the

 

systems-management

 

software

 

can

 

turn

 

on

 

the

 

server.

Note:

 

When

 

4

 

GB

 

or

 

more

 

of

 

memory

 

(physical

 

or

 

logical)

 

is

 

installed,

 

some

 

memory

 

is

 

reserved

 

for

 

various

 

system

 

resources

 

and

 

is

 

unavailable

 

to

 

the

 

operating

 

system.

 

The

 

amount

 

of

 

memory

 

that

 

is

 

reserved

 

for

 

system

 

resources

 

depends

 

on

 

the

 

operating

 

system,

 

the

 

configuration

 

of

 

the

 

server,

 

and

 

the

 

configured

 

peripheral

 

component

 

interconnect

 

(PCI,

 

PCI

 

Express,

 

or

 

PCI-X)

 

options.

 

 

Chapter

 

1.

 

The

 

ThinkServer

 

TD100

 

and

 

TD100x

 

server

 

13