Страница: 58 из 76
Note:
All
configuration
settings
will
be
cleared
by
this
action;
you
might
have
to
configure
the
settings
again.
1.
Review
the
safety
information
that
begins
on
page
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
power
cords
and
external
cables.
3.
Remove
the
server
from
the
rack
and
place
it
on
a
flat,
static-protective
surface.
4.
Remove
the
cover.
See
for
instructions.
5.
If
necessary,
remove
the
riser-card
assembly.
See
for
instructions.
6.
Move
the
clear-CMOS
jumper
1
from
pins
1
and
2
to
pins
2
and
3
and
leave
it
there
for
at
least
5
seconds;
then,
move
the
clear-CMOS
jumper
back
to
pins
1
and
2.
7.
Reinstall
the
riser-card
assembly
and
cover.
See
for
instructions.
8.
Replace
the
server
in
the
rack
and
connect
the
server
to
a
keyboard,
monitor,
and
mouse;
then,
connect
the
server
to
a
power
source.
9.
Turn
on
the
server.
You
can
now
start
the
Configuration/Setup
Utility
program
and
either
delete
the
old
password
or
set
a
new
power-on
or
administrator
password.
Using
the
LSI
Logic
Configuration
Utility
program
Use
the
LSI
Logic
Configuration
Utility
program
to
configure
hot-swap
hard
disk
drives
that
are
connected
to
the
SAS/SATA
controller.
Important:
v
If
the
server
is
a
simple-swap
SATA
model
that
contains
a
SATA
RAID
back
plate,
you
can
use
the
LSI
Logic
Configuration
Utility
program
to
configure
the
simple-swap
SATA
hard
disk
drives.
v
If
you
install
an
optional
RAID
controller
in
the
server,
such
as
the
ServeRAID-MR10i
controller,
use
the
configuration
software
that
comes
with
the
adapter
to
configure
the
hard
disk
drives.
Starting
the
LSI
Logic
Configuration
Utility
program
To
start
the
LSI
Logic
Configuration
Utility
program,
complete
the
following
steps:
1.
Turn
on
the
server.
2.
When
the
prompt
Press
CTRL-C
to
start
LSI
Logic
Configuration
Utility...
is
displayed,
press
Ctrl+C.
If
you
have
set
an
administrator
password,
you
are
prompted
to
type
the
password.
3.
Use
the
arrow
keys
to
select
the
adapter
(SAS
controller)
for
which
you
want
to
change
settings.
Use
the
Help
function
to
see
instructions
and
available
actions
for
this
screen.
4.
To
change
the
settings
of
the
selected
items,
follow
the
instructions
on
the
screen.
5.
Press
Enter
to
save
your
changes.
Configuring
the
controller
and
devices
To
configure
a
SAS
controller
and
attached
devices,
select
the
controller
from
the
initial
LSI
Logic
Configuration
Utility
program
screen;
then,
press
Enter.
You
can
view
and
change
settings
for
the
following
items
for
the
selected
controller:
44
ThinkServer
RS110
Types
6435,
6436,
6437
and
6438:
User
Guide