Updating the server configuration Адаптер thinkserver Lenovo Rack Server - RS110 (ThinkServer) - Type 6436

Страница: 50 из 76

background image

Rear

  

 

 

1

 

Power-cord

 

connector

 

5

 

Ethernet

 

1

 

connector

 

2

 

Systems-management

 

connector

 

6

 

Ethernet

 

2

 

connector

 

3

 

USB

 

3

 

connector

 

7

 

Video

 

connector

 

4

 

USB

 

4

 

connector

 

8

 

Serial

 

connector

  

You

 

must

 

turn

 

off

 

the

 

server

 

before

 

you

 

connect

 

or

 

disconnect

 

cables.

 

See

 

the

 

documentation

 

that

 

comes

 

with

 

any

 

external

 

devices

 

for

 

additional

 

cabling

 

instructions.

 

It

 

might

 

be

 

easier

 

for

 

you

 

to

 

route

 

cables

 

before

 

you

 

connect

 

the

 

devices

 

to

 

the

 

server.

 

Cable

 

identifiers

 

are

 

printed

 

on

 

the

 

cables

 

that

 

come

 

with

 

the

 

server

 

and

 

devices.

 

Use

 

these

 

identifiers

 

to

 

connect

 

the

 

cables

 

to

 

the

 

correct

 

connectors.

 

If

 

the

 

server

 

comes

 

with

 

an

 

installed

 

operating

 

system,

 

see

 

the

 

documentation

 

that

 

comes

 

with

 

the

 

operating

 

system

 

for

 

additional

 

cabling

 

instructions.

 

There

 

is

 

no

 

keyboard

 

connector

 

or

 

mouse

 

connector

 

on

 

the

 

server.

 

You

 

can

 

connect

 

a

 

USB

 

keyboard

 

and

 

USB

 

mouse

 

to

 

the

 

server

 

by

 

using

 

the

 

USB

 

connectors.

 

Updating

 

the

 

server

 

configuration

 

When

 

you

 

start

 

the

 

server

 

for

 

the

 

first

 

time

 

after

 

you

 

add

 

or

 

remove

 

an

 

internal

 

optional

 

device

 

or

 

external

 

SAS

 

device,

 

you

 

might

 

receive

 

a

 

message

 

that

 

the

 

configuration

 

has

 

changed.

 

The

 

Configuration/Setup

 

Utility

 

program

 

starts

 

automatically

 

so

 

that

 

you

 

can

 

save

 

the

 

new

 

configuration

 

settings.

 

For

 

more

 

information,

 

see

 

Chapter

 

3,

 

“Configuring

 

the

 

server,”

 

on

 

page

 

37.

 

Some

 

optional

 

devices

 

have

 

device

 

drivers

 

that

 

you

 

must

 

install.

 

For

 

information

 

about

 

installing

 

device

 

drivers,

 

see

 

the

 

documentation

 

that

 

comes

 

with

 

each

 

device.

 

If

 

the

 

server

 

has

 

a

 

RAID

 

configuration

 

that

 

uses

 

the

 

SAS/SATA

 

controller

 

with

 

integrated

 

RAID

 

(hot-swap

 

SATA

 

or

 

SAS

 

models

 

only)

 

and

 

you

 

have

 

installed

 

or

 

removed

 

a

 

hard

 

disk

 

drive,

 

you

 

might

 

have

 

to

 

reconfigure

 

the

 

disk

 

arrays.

 

If

 

the

 

server

 

has

 

an

 

optional

 

RAID

 

adapter

 

and

 

you

 

have

 

installed

 

or

 

removed

 

a

 

hard

 

disk

 

drive,

 

see

 

the

 

documentation

 

that

 

comes

 

with

 

the

 

RAID

 

adapter

 

for

 

information

 

about

 

reconfiguring

 

the

 

disk

 

arrays.

 

If

 

the

 

server

 

is

 

a

 

simple-swap

 

model

 

that

 

contains

 

a

 

SATA

 

RAID

 

back

 

plate,

 

you

 

can

 

use

 

the

 

LSI

 

Logic

 

Configuration

 

Utility

 

program

 

to

 

configure

 

the

 

simple-swap

 

SATA

 

hard

 

disk

 

drives.

 

For

 

information

 

about

 

configuring

 

an

 

integrated

 

Gigabit

 

Ethernet

 

controller,

 

see

 

“Configuring

 

the

 

Gigabit

 

Ethernet

 

controllers”

 

on

 

page

 

46.

 

 

36

 

ThinkServer

 

RS110

 

Types

 

6435,

 

6436,

 

6437

 

and

 

6438:

 

User

 

Guide