Installing a hot-swap hard disk drive Адаптер thinkserver Lenovo Rack Server - RS110 (ThinkServer) - Type 6436

Страница: 42 из 76

background image

Installing

 

a

 

hot-swap

 

hard

 

disk

 

drive

 

The

 

3.5-inch

 

drive

 

hot-swap

 

server

 

models

 

support

 

either

 

two

 

SAS

 

3.5-inch

 

hard

 

disk

 

drives

 

or

 

two

 

SATA

 

3.5-inch

 

hard

 

disk

 

drives.

 

The

 

2.5-inch

 

drive

 

hot-swap

 

server

 

models

 

support

 

four

 

2.5-inch

 

SAS

 

hard

 

disk

 

drives

 

1.

 

  

 

The

 

installation

 

procedure

 

is

 

the

 

same

 

for

 

any

 

of

 

these

 

drives.

 

The

 

illustrations

 

in

 

this

 

procedure

 

show

 

3.5-inch

 

SAS

 

drives.

 

To

 

install

 

a

 

hot-swap

 

hard

 

disk

 

drive,

 

complete

 

the

 

following

 

steps.

 

Note:

 

If

 

you

 

have

 

only

 

one

 

hard

 

disk

 

drive,

 

install

 

it

 

in

 

the

 

left

 

or

 

upper-left

 

drive

 

bay.

  

 

Attention:

  

To

 

avoid

 

damage

 

to

 

the

 

hard

 

disk

 

drive

 

connectors,

 

make

 

sure

 

that

 

the

 

cover

 

is

 

in

 

place

 

and

 

fully

 

closed

 

whenever

 

you

 

install

 

or

 

remove

 

a

 

hard

 

disk

 

drive.

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

19.

 

2.

   

Make

 

sure

 

that

 

the

 

server

 

cover

 

is

 

in

 

place

 

and

 

fully

 

closed.

 

3.

   

Remove

 

the

 

filler

 

3

 

panel

 

from

 

the

 

bay.

 

 

Attention:

  

To

 

maintain

 

proper

 

system

 

cooling,

 

do

 

not

 

operate

 

the

 

server

 

for

 

more

 

than

 

10

 

minutes

 

without

 

either

 

a

 

drive

 

or

 

filler

 

panel

 

installed

 

in

 

each

 

bay.

 

4.

   

Install

 

the

 

hard

 

disk

 

drive

 

in

 

the

 

hot-swap

 

bay:

 

a.

   

Make

 

sure

 

that

 

the

 

drive

 

handle

 

2

 

is

 

open

 

(that

 

is,

 

perpendicular

 

to

 

the

 

front

 

of

 

the

 

drive).

 

b.

   

Align

 

the

 

drive

 

assembly

 

1

 

with

 

the

 

guide

 

rails

 

in

 

the

 

bay.

 

c.

   

Gently

 

push

 

the

 

drive

 

assembly

 

into

 

the

 

bay

 

until

 

the

 

drive

 

stops.

 

 

28

 

ThinkServer

 

RS110

 

Types

 

6435,

 

6436,

 

6437

 

and

 

6438:

 

User

 

Guide