Installing a simple-swap Serial ATA hard disk drive Адаптер thinkserver Lenovo Rack Server - RS110 (ThinkServer) - Type 6436

Страница: 41 из 76

background image

Note:

 

If

 

you

 

have

 

only

 

one

 

hard

 

disk

 

drive,

 

install

 

it

 

in

 

the

 

left

 

drive

 

bay.

  

 

 

1

 

SATA

 

hard

 

disk

 

drive

 

back

 

plate

 

3

 

Hard

 

disk

 

drive

 

assembly

 

2

 

Filler

 

panel

 

  

 

Attention:

  

To

 

avoid

 

damage

 

to

 

the

 

hard

 

disk

 

drive

 

connectors,

 

make

 

sure

 

that

 

the

 

cover

 

is

 

in

 

place

 

and

 

fully

 

closed

 

whenever

 

you

 

install

 

or

 

remove

 

a

 

hard

 

disk

 

drive.

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

19.

 

2.

   

Make

 

sure

 

that

 

the

 

server

 

cover

 

is

 

in

 

place

 

and

 

fully

 

closed.

 

3.

   

Turn

 

off

 

the

 

server

 

and

 

peripheral

 

devices,

 

and

 

disconnect

 

the

 

power

 

cord

 

and

 

all

 

external

 

cables.

 

4.

   

Remove

 

the

 

filler

 

panel

 

from

 

the

 

bay.

 

5.

   

Pull

 

the

 

loops

 

of

 

the

 

drive

 

tray

 

toward

 

each

 

other,

 

and

 

slide

 

the

 

drive

 

into

 

the

 

server

 

until

 

the

 

drive

 

connects

 

to

 

the

 

back

 

plate.

 

6.

   

Release

 

the

 

loops

 

of

 

the

 

drive

 

tray.

 

7.

   

Insert

 

the

 

filler

 

panel

 

into

 

the

 

bay

 

to

 

cover

 

the

 

drive.

 

If

 

you

 

have

 

other

 

devices

 

to

 

install,

 

do

 

so

 

now.

 

Otherwise,

 

go

 

to

 

“Completing

 

the

 

installation”

 

on

 

page

 

35.

 

Note:

 

If

 

a

 

RAID

 

controller

 

or

 

adapter

 

is

 

installed,

 

you

 

might

 

have

 

to

 

reconfigure

 

the

 

disk

 

arrays

 

after

 

you

 

install

 

hard

 

disk

 

drives.

 

See

 

your

 

RAID

 

controller

 

or

 

adapter

 

documentation.

 

To

 

remove

 

a

 

simple-swap

 

SATA

 

drive

 

from

 

the

 

bay,

 

complete

 

the

 

following

 

steps:

 

1.

   

Read

 

the

 

safety

 

information

 

that

 

begins

 

on

 

page

 

v

 

and

 

“Installation

 

guidelines”

 

on

 

page

 

19.

 

2.

   

Turn

 

off

 

the

 

server

 

and

 

peripheral

 

devices,

 

and

 

disconnect

 

the

 

power

 

cord

 

and

 

all

 

external

 

cables.

 

3.

   

Remove

 

the

 

filler

 

panel

 

from

 

the

 

bay.

 

4.

   

Pull

 

the

 

loops

 

of

 

the

 

drive

 

tray

 

toward

 

each

 

other

 

and

 

pull

 

the

 

tray

 

out

 

of

 

the

 

bay.

 

Chapter

 

2.

 

Installing

 

optional

 

devices

 

27