Installing an adapter Адаптер thinkserver Lenovo Rack Server - RS110 (ThinkServer) - Type 6436

Страница: 36 из 76

background image

2.

   

Turn

 

off

 

the

 

server

 

and

 

all

 

attached

 

devices

 

(see

 

“Turning

 

off

 

the

 

server”

 

on

 

page

 

9).

 

3.

   

Disconnect

 

all

 

external

 

cables

 

and

 

power

 

cords.

 

4.

   

Remove

 

the

 

server

 

from

 

the

 

rack

 

and

 

place

 

it

 

on

 

a

 

flat,

 

static-protective

 

surface.

  

  

5.

   

Press

 

the

 

cover-release

 

button

 

1.

 

6.

   

Slide

 

the

 

cover

 

back

 

approximately

 

1.27

 

cm

 

(0.5

 

inches);

 

then,

 

lift

 

it

 

off

 

the

 

server.

 

Attention:

  

For

 

proper

 

cooling

 

and

 

airflow,

 

replace

 

the

 

cover

 

before

 

you

 

turn

 

on

 

the

 

server.

 

Operating

 

the

 

server

 

for

 

extended

 

periods

 

of

 

time

 

(more

 

than

 

30

 

minutes)

 

with

 

the

 

cover

 

removed

 

might

 

damage

 

server

 

components.

 

Installing

 

an

 

adapter

 

The

 

following

 

notes

 

describe

 

the

 

types

 

of

 

adapters

 

that

 

the

 

server

 

supports

 

and

 

other

 

information

 

that

 

you

 

must

 

consider

 

when

 

you

 

install

 

an

 

adapter:

 

v

   

Locate

 

the

 

documentation

 

that

 

comes

 

with

 

the

 

adapter

 

and

 

follow

 

those

 

instructions

 

in

 

addition

 

to

 

the

 

instructions

 

in

 

this

 

section.

 

If

 

you

 

have

 

to

 

change

 

switch

 

settings

 

or

 

jumper

 

settings

 

on

 

the

 

adapter,

 

follow

 

the

 

instructions

 

that

 

come

 

with

 

the

 

adapter.

 

v

   

The

 

adapter

 

slots

 

are

 

on

 

the

 

riser-card

 

assembly.

 

You

 

must

 

first

 

remove

 

the

 

riser-card

 

assembly

 

to

 

access

 

the

 

adapter

 

slots.

 

v

   

The

 

two

 

PCI

 

Express

 

slots

 

on

 

the

 

riser-card

 

assembly

 

support

 

PCI

 

Express

 

x8

 

1.0a

 

adapters.

 

v

   

You

 

can

 

install

 

one

 

full-height

 

three-quarter-length

 

adapter

 

in

 

expansion

 

slot

 

1

 

and

 

one

 

low-profile

 

half-length

 

adapter

 

in

 

expansion

 

slot

 

2.

 

Note:

 

When

 

the

 

optional

 

Remote

 

Supervisor

 

Adapter

 

II

 

SlimLine

 

is

 

installed

 

in

 

the

 

server,

 

you

 

can

 

install

 

only

 

a

 

half-length

 

adapter

 

in

 

expansion

 

slot

 

1.

 

v

   

If

 

you

 

have

 

installed

 

an

 

optional

 

PCI-X

 

riser-card

 

assembly

 

in

 

the

 

server,

 

you

 

can

 

install

 

a

 

full-height,

 

three-quarter-length

 

PCI-X

 

64/133

 

MHz

 

adapter

 

in

 

the

 

PCI-X

 

slot

 

on

 

the

 

riser-card

 

assembly.

 

Note:

 

When

 

the

 

optional

 

Remote

 

Supervisor

 

Adapter

 

II

 

SlimLine

 

is

 

installed

 

in

 

the

 

server,

 

you

 

can

 

install

 

only

 

a

 

half-length

 

adapter

 

in

 

the

 

PCI-X

 

slot.

 

v

   

An

 

optional

 

Remote

 

Supervisor

 

Adapter

 

II

 

SlimLine

 

can

 

be

 

installed

 

only

 

in

 

the

 

dedicated

 

connector

 

on

 

the

 

system

 

board

 

(see

 

“System-board

 

optional-device

 

 

22

 

ThinkServer

 

RS110

 

Types

 

6435,

 

6436,

 

6437

 

and

 

6438:

 

User

 

Guide