Rear view Адаптер thinkserver Lenovo Rack Server - RS110 (ThinkServer) - Type 6436

Страница: 22 из 76

background image

Note:

 

If

 

this

 

LED

 

is

 

off,

 

it

 

does

 

not

 

mean

 

that

 

there

 

is

 

no

 

electrical

 

power

 

in

 

the

 

server.

 

The

 

LED

 

might

 

be

 

burned

 

out.

 

To

 

remove

 

all

 

electrical

 

power

 

from

 

the

 

server,

 

you

 

must

 

disconnect

 

the

 

power

 

cord

 

from

 

the

 

electrical

 

outlet.

 

Power-control

 

button:

 

Press

 

this

 

button

 

to

 

turn

 

the

 

server

 

on

 

and

 

off

 

manually.

 

A

 

power-control-button

 

shield

 

comes

 

installed

 

around

 

the

 

button

 

to

 

prevent

 

the

 

server

 

from

 

being

 

turned

 

off

 

accidentally.

 

You

 

can

 

remove

 

this

 

disk-shaped

 

shield

 

if

 

you

 

prefer.

 

Reset

 

button:

 

Press

 

this

 

button

 

to

 

reset

 

the

 

server

 

and

 

run

 

the

 

power-on

 

self-test

 

(POST).

 

You

 

might

 

have

 

to

 

use

 

a

 

pen

 

or

 

the

 

end

 

of

 

a

 

straightened

 

paper

 

clip

 

to

 

press

 

the

 

button.

 

Hard

 

disk

 

drive

 

activity

 

LED:

 

When

 

this

 

LED

 

is

 

flashing,

 

it

 

indicates

 

that

 

a

 

hard

 

disk

 

drive

 

is

 

in

 

use.

 

Locator

 

LED:

 

This

 

LED

 

can

 

be

 

lit

 

remotely

 

by

 

the

 

system

 

administrator

 

to

 

aid

 

in

 

visually

 

locating

 

the

 

server.

 

Rear

 

view

 

The

 

following

 

illustration

 

shows

 

the

 

LEDs

 

on

 

the

 

rear

 

of

 

the

 

server.

 

  

 

 

1

 

Ethernet

 

1

 

activity

 

LED

 

3

 

Ethernet

 

2

 

activity

 

LED

 

2

 

Ethernet

 

1

 

link

 

LED

 

4

 

Ethernet

 

2

 

link

 

LED

  

Ethernet

 

activity

 

LED:

 

This

 

LED

 

is

 

on

 

each

 

Ethernet

 

connector.

 

When

 

this

 

LED

 

is

 

lit,

 

it

 

indicates

 

that

 

there

 

is

 

activity

 

between

 

the

 

server

 

and

 

the

 

network.

 

Ethernet

 

link

 

LED:

 

This

 

LED

 

is

 

on

 

each

 

Ethernet

 

connector.

 

When

 

this

 

LED

 

is

 

lit,

 

it

 

indicates

 

that

 

the

 

Ethernet

 

controller

 

is

 

connected

 

to

 

the

 

network.

 

The

 

following

 

illustration

 

shows

 

the

 

connectors

 

on

 

the

 

rear

 

of

 

the

 

server.

 

  

 

 

1

 

Power-cord

 

connector

 

5

 

Ethernet

 

1

 

connector

 

2

 

Systems-management

 

connector

 

6

 

Ethernet

 

2

 

connector

 

3

 

USB

 

3

 

connector

 

7

 

Video

 

connector

 

4

 

USB

 

4

 

connector

 

8

 

Serial

 

connector

  

Power-cord

 

connector:

 

Connect

 

the

 

power

 

cord

 

to

 

this

 

connector.

 

 

8

 

ThinkServer

 

RS110

 

Types

 

6435,

 

6436,

 

6437

 

and

 

6438:

 

User

 

Guide